Chimney Rebuild in Stuart, FL
Rebuild only as much as the masonry needs, matched to the house.
- Family owned and run
- Licensed & insured
- Same-day service
- Locally run
Get Your Free Inspection
About thirty seconds
Request received
Thank you. Someone from our family crew will call you to set a time for the free inspection.
Quicker by phone? Call (772) 610-6329
Short answer
Rebuilding a chimney means taking down masonry that is too damaged to repair and relaying it with sound brick and mortar. A partial chimney rebuild often covers only the courses above the roofline, while a full rebuild goes down further when the stack leans or the damage runs deep. A new crown and flashing finish the job.
Free Inspection, Then 10% Off the Work
Book your chimney rebuild within 72 hours of the free inspection and 10% comes off the work.
What You Can Count On
-
Upfront pricing
How many courses come down, and the price, are agreed in writing first.
-
Experienced crew
The experienced crew we send relays brick to match the rest of the chimney.
-
Workmanship warranty
Our workmanship warranty covers the masonry we rebuild.
On this page
Repair or Rebuild
Most chimney problems can be repaired. A chimney rebuild becomes the honest answer when the masonry has lost its strength: bricks loose enough to lift out by hand, mortar washed out deep into the joints, or a stack that has started to move. Patching that kind of damage only delays a bigger job and leaves a falling hazard on the roof.
Partial Chimney Rebuild
The part above the roof takes the most weather, so it usually fails first. Rebuild chimney above roofline work takes the stack down to sound masonry, often a few feet below the top, and relays it. We reuse good brick where it matches and add new brick where needed, then pour a new crown and set new counter flashing into the fresh mortar joints.
Full Chimney Rebuild and Leaning Chimneys
A full chimney rebuild takes the masonry down further, sometimes to the roof deck or below, when damage runs through the stack. Leaning chimney repair depends on why it leans: a failed footing needs a different answer than a top section that has shifted. We look at the base and the attic before recommending how far chimney reconstruction should go.
How We Protect Your Roof
Rebuilding means heavy material on the roof. We stage brick and mortar carefully, protect the shingles or tile around the stack, lower debris rather than throw it, and clean the roof and gutters when we finish. As your chimney rebuild contractor, we also handle the permit when the scope requires one.
Matching the House
Chimney rebuilding should look like it belongs. We match brick size, color and mortar joint style as closely as the available materials allow, so the rebuilt section blends with the rest of the chimney and the house.
How a Chimney Rebuild Goes
-
Decide the scope
Find where sound masonry starts and how far to go.
-
Take it down
Course by course, with the roof protected.
-
Relay the stack
Matched brick and mortar, with a new crown on top.
-
Flash and cap
New counter flashing and a cap to finish.
Book Your Free Stuart Inspection
A short form, a quick call back, and a time that suits you.
- Inspection first, estimate in writing
- Upfront pricing, no hidden fees
- Family owned and operated
Request received
Thank you. Someone from our family crew will call you to set a time for the free inspection.
What the Written Estimate Covers
- Deciding how many courses need to come down
- Taking the masonry down and protecting the roof
- Relaying brick with matched mortar and a new crown
- New flashing, a cap and the written price
Questions We Answer Often
How long does it take to rebuild a chimney?
A partial rebuild of the stack above the roof usually takes one to three working days, plus curing time for the new crown. A full rebuild takes longer, depending on the height and access; rain days and permits can stretch the schedule, so we give you a realistic plan before starting.
When should a chimney be rebuilt?
Rebuild a chimney once bricks are loose enough to move by hand, mortar crumbles deep into the joints or the stack has started to lean. Repeated leaks after earlier repairs are another sign. If the masonry is sound underneath, repointing and a new crown are usually enough.
How is a chimney stack rebuilt?
First the stack is taken down course by course until the crew reaches sound masonry. Then the brick is relaid with matched mortar, a new crown is poured and new counter flashing is set into the fresh joints. A cap finishes the top.
Can a leaning chimney be saved?
Sometimes. When only the top section has shifted, rebuilding that part straightens the chimney. When the whole stack leans because the footing has settled, the base has to be addressed too, and a full rebuild may be the safer choice; we check the footing and the attic before advising.
Do I need a permit to rebuild my chimney?
Many building departments require a permit for a chimney rebuild, especially when the work goes below the roofline or changes the structure. Rules vary by jurisdiction. When your job needs one, we list the permit on the written estimate and handle the paperwork before the masonry comes down.
Can a homeowner rebuild a chimney themselves?
Rebuilding a chimney means working at height with heavy brick, matching mortar to old masonry and setting flashing and a crown that keep water out. Small repointing jobs are within reach of a careful owner, but a rebuild usually needs a permit and a crew with staging; mistakes at the top tend to show up as leaks inside.
Proudly American
Family owned in Stuart, with an experienced crew, upfront pricing and a workmanship warranty on the work we do.
Chimney & Fireplace Brands We Work With
Copperfield Chimney Supply 
DuraVent 
Heat & Glo 
Heatilator 
Olympia Chimney and Venting 
Rutland
Get a Straight Answer on the Rebuild
Before anything comes down, a free look tells you whether a partial rebuild, a full one or plain repairs will do.